The drill is a cutting part that is always used in conjunction with a mechanical tool called a drill or any other related machine. It can be used to make holes or perforations, drill metal, wood and other materials. Some are versatile and in turn one of them can be used to work with various materials such as those mentioned above.
The drills themselves are used for cutting, by means of perforations, lateral cuts as the spiral drill does, dry cut ceramic drills, plaster wall carrying drills, among others. They are used in different materials that exist such as wood, light metals, ferrous metals, rocks, ceramics, plaster, etc.
There are many types of wooden drills, namely, bits, pallet drills, drill bits, or crown saws, among others. In addition, there are specials suitable for specific woodworking tasks.
Brad point drills are also known as shank or W point drills. They can be recognized by the small dot at the end of the bit. The drill has spurs on each side of the point that are designed to cut clean, straight holes in all types of wood.
Drills are used to make large, deep and precise holes in dry wood. They have spiral shafts that reach fine, threaded points.
Popsicle bits are also called wooden spade bits. These drills have a pointed tip that starts the hole. The shovel-shaped blade follows to drill a large, wide hole. With shovel tips, the size of the drill bit is usually indicated on the face of the paddle. Sizes vary from 6 to 38 millimeters in diameter.
The Wood Auger drill is perfect for drilling large, deep holes in wood and large man-made boards. For the most part, a drill is used only as part of a hand wrench. These drills cut perfect, deep, flat-bottomed holes.
Generally referred to as drilling lathes, these are probably the most widely recognized drilling tools used by a one-handed maintenance personnel or an electric drill.
The leading edges cut through the material while the spirals remove debris from the hole and keep the tip straight. They can be used on wood, metal, plastics and comparative materials.
Using Metal Drills
Metal drills are also known as high speed steel (HSS) or twist drills. They are usually black in color and can be used for wood and plastic. While HSS drills can be used for drilling plastic and wood, wood drills should never be used for drilling metal.
When you are going to drill many holes or need to drill hard and abrasive metals such as stainless steel or cast iron, you need black oxide or a cobalt metal drill.
For rougher or harder metals (such as stainless steel), chrome/vanadium, cobalt or titanium carbide drills are ideal. HSS means that the drill is made of a harder metal.
Some drills also have a special coating called titanium nitride (TiN), which helps resist heat and friction better, making these drills last up to six times longer than standard high-speed steel drills.
When drilling stainless steel, it is best to use a cobalt alloy high speed steel (HSS-E) drill or drills that are coated with titanium. These are more expensive than conventional HSS drills, but allow you to drill in special steel without causing wear on the drill.
To be sure of which hole we have to make, it is necessary to know the diameter of the drill to be used, depending on the measures and type of the thread. For the metric thread, we have that within “metric” we can distinguish two types of thread, which are the normal metric and the fine thread metric.
These are some metal drills with their respective diameter in inches and millimeters:
These drills are used to drill bricks, stones etc. They have a reinforcement in the head that gives them a “shovel” shape since it is reinforced with a very hard material to increase its duration and guarantee its drilling capacity. Tungsten carbide plate laminated drill bit (widia). The body is laminated and is perfectly designed for plaster, cement, brick, uralite, sandstone and limestone.
The body is milled, and in addition to all the above materials, it can easily drill into marble, concrete, slate, granite and usually all types of stone. Its power of penetration and its duration is above the characteristics of the previous one.
Titanium coated drills produce less friction. They are stronger than basic HSS bits and stay in place longer. They work for drilling wood, metal, fiberglass and PVC.
Cobalt drills are extremely hard and dissipate heat quickly. They are mainly used for drilling aluminum and hard metals such as stainless steel.
A masonry drill bit drills through hard materials such as concrete, brick, concrete and other masonry. Some work with a standard corded or cordless rotary drill, but those designed for use with a rotary hammer or hammer drill can drill masonry more effectively.
Bits that can drill through concrete or masonry are called masonry bits. They are also good for drilling brick and stone. Tungsten carbide tipped bits are the strongest; when it comes to solid concrete, the sharper the better. Masonry bits cut holes through concrete in two steps.
The tile bit is used to drill ceramic or glass tiles and has a ground tungsten carbide tip. However, these drills can be used with a hand drill and are best used for drilling with speed, from inconsistent to moderate speed.
During the installation of ceramic tiles, the tile repairer must deal with situations where the best option is to use tile crown drills. The need to drill holes in ceramic tile for water supplies, drains, or electrical connections requires the use of wreath bits.
The Solomonic drill is used to drill wood quickly and accurately. It is perfect for use in construction, carpentry and roofing activities. It is also used for soft and hard woods. The drill has a hexagonal insertion shank system and works with any drill with a 13 mm chuck
SDS drills, which are different from conventional drills, have a direct entry, different in thickness and design, which in turn provides better performance than conventional drills because they allow for higher speeds.
High Speed Steel (HSS) drills can drill wood, fiberglass, PVC (polyvinyl chloride) and soft metals such as aluminum.
The HSS-E drill is a high performance cobalt alloy drill. Even with insufficient cooling it has a reserve in heat resistance. Due to the addition of 5% Co alloy in the cutting material, these drills can be used to work with workpieces with a tensile strength of more than 800 N/m².
These are drills composed of a shank and a tungsten carbide tip (widea) that are similar in shape to a spearhead. It is used to drill glass, ceramics, tiles, porcelain, mirrors, etc.
Sandvik is an engineering group in mining and rock excavation, metal cutting and materials technology. Sandvik designs are known and widely used all over the world. Regardless of the conditions they encounter, these tools make the work more efficient and easier.
They are equipped with Sandvik’s patented cemented carbide buttons, which are designed to drill more. The drill bodies are made of precision chrome molybdenum steel with a compound curve shape for faster, smoother cutting and easier removal of cuttings. The drills in the new range have an optimized head length with maximized steel support for the cemented carbide buttons, deep face grooves for excellent flushing and aggressive cutting structure.
The types of drills for do-it-yourself work are as follows:
Sharpening a drill by hand can be a challenge. It is important to grind the drill at the right angle and doing so with your free hand makes this almost impossible. To make sure you grind the drill at the right angle, you can use a template.
Follow these steps and you can transform your used, dull, chipped or broken drill into a main hole blasting instrument with a bench grinder or belt grinder.
Choose your Sharpening Tool
Either a bench grinder or a belt sander will work to sharpen the bits, just make sure the guards on either of these machines are less than 1/8″ away from the belt or wheel so that your bit does not get caught in the guard!
Practice Holding the Drill
Start in a comfortable position with your hand against the machine stand and hold the drill in both hands. Hold the drill at a 60 degree angle to the face of the belt sander. Place the end of the landing so that it is directly against the belt.
Cutting the Landing
Cut the rest by raising your right hand while applying pressure to the grinding device.
Form the Chisel
By moving your left hand to the right, create the chisel angle. Practice a few times until the chisel angle is 45 degrees from the lip.
Form the Landing
By rotating or turning the drill counter-clockwise, create a rounded rest that provides more support to the lip.
Combine Cutting, Shaping and Rotation
Combine the three movements while sharpening to make the perfect cut on the face of the drill. Repeat this step a couple of times and turn the drill 180 degrees by hand to sharpen the other lip
There are different types of drills according to the work you want to do. They can be differentiated by their forms and materials of manufacture.
Mainly speaking, you can judge them by the shape. HSS (for metal) drills are solid steel, carbide tipped drills (SDS) are inserted carbide tipped drills, suitable for drilling in masonry, concrete, etc. Brad (triple point) tipped drills, and spade drills are generally for wood.
Other Materials in ALPHAPEDIA
Other Products of Interest in ALPHAPEDIA
Other Topics of Interest in ALPHAPEDIA
Esta web usa cookies.